Lenoxx Electronics CD 163 User Manual

®
COMPACT DISC PLAYER  
AM/FM DUAL CASSETTE RECORDER  
WITH REMOTE CONTROL  
MODEL CD-163  
OPERATING INSTRUCTIONS  
INCLUDES FULL FEATURE REMOTE CONTROL  
MULTI-COLORED FLUORESCENT DISPLAY  
PLAYS MUSIC COMPACT DISCS  
KARAOKE FUNCTION WITH DUAL MIC. JACKS  
FULLY PROGRAMMABLE CD PLAYER WITH REPEAT PLAY  
RECEIVES AM/FM STEREO BROADCASTS  
ROTARY BASS & TREBLE CONTROLS  
RECORDS FROM CD, TAPE OR RADIO  
2 WAY POWER - AC/DC  
REQUIRES 8 SIZE “D” BATTERIES (NOT INCLUDED)  
PLEASE READ CAREFULLY BEFORE USE  
IB-CD163(TA)-FRED’S-E-042602  
ADDITIONAL SAFETY INSTRUCTIONS  
1. Power Sources - The appliance should be connected to a power supply only of the type  
described in the operating instructions or as marked on the appliance.  
2. Wall or Ceiling Mounting - The appliance should not be mounted to a wall or ceiling.  
3. Object and Liquid Entry - Care should be taken so that objects do not fall and liquids  
are not spilled into the enclosure through openings.  
4. Servicing - The user should not attempt to service the appliance beyond that described in  
the operating instructions. All other servicing should be referred to qualified service personnel.  
It is the intent of Lenoxx that this product be used in full compliance with the  
copyright laws of the United States and that prior permission be obtained from  
copyright owners whenever recording songs from the RADIO or CD’s.  
Do not apply oil or petroleum products or solvents to any part of this set.  
CAUTION  
Use of controls or adjustments or performance of procedures other than those  
specified herein may result in hazardous radiation exposure.  
This compact disc player is classified as CLASS 1 LASER PRODUCT as stated  
on the back of the set.  
2
IB-CD163(TA)-FRED’S-E-042602  
BATTERY SAFETY INSTRUCTIONS  
CAUTION:  
TO REDUCE THE RISK OF FIRE OR PERSONAL INJURY OR DAMAGE TO YOUR  
SET, READ AND FOLLOW THESE INSTRUCTIONS.  
1. Use only the type and size of batteries mentioned in the operating instructions  
booklet (batteries are not included with this set, please buy the proper batteries).  
2. Do not dispose the batteries into a fire. The cells may explode. Check with local  
codes for possible special disposal instructions.  
3. Do not open or mutilate the batteries. Released electrolyte is corrosive and may  
cause damage to the eyes or skin. It may be toxic if swallowed.  
4. Be careful when handling batteries in order not to short the battery with conducting  
materials such as rings, bracelets and keys. The battery or conductor may over  
heat and cause burns.  
5. Do not attempt to recharge non-rechargeable batteries. The batteries may leak  
corrosive electrolyte or explode.  
6. Do not attempt to rejuvenate the batteries identified for use with this product by  
heating them. Sudden release of the battery electrolyte may cause burns or  
irritation to eyes or skin.  
7. All batteries should be replaced at the same time. Mixing fresh and discharged  
batteries could increase internal cell pressure and rupture the batteries.  
8. When inserting batteries into this product, the proper polarity (  
and  
) or  
direction must be observed. Reverse insertion of some or all of the batteries may  
result in battery electrolyte leakage or explosion.  
9. Remove the batteries from this product if the product will not be used for a long  
period of time (several months or more) since during the period the batteries could  
leak, damaging the product.  
10. Discard weak or dead batteries as soon as possible since they are more likely to  
leak in the product. Batteries should be replaced (depending on the product) when  
the display gets dim or if the Low Battery Indicator shows or if the sound gets  
distorted.  
11. Do not store this product in high temperature areas. Batteries that are stored in a  
freezer or refrigerator for the purpose of extending shelf life should be protected  
from condensation during storage and defrosting. Batteries should be stabilized at  
room temperature prior to use after cold storage.  
12. If this product does not operate normally, see TROUBLE SHOOTING in this  
instruction manual. If you can’t resolve the problem, or if the product is damaged, refer to the  
LENOXX WARRANTY INFORMATION. Opening or removing covers may expose you to  
dangerous voltages or other risks. Incorrect reassembly can cause electric shock when  
the appliance is subsequently used.  
13. If liquid leaks from the batteries, carefully wipe this liquid. Do not allow it to touch your skin,  
and discard the leaking batteries.  
14. Do not mix batteries (OLD and NEW or CARBON and ALKALINE, etc.).  
15. The use of rechargeable batteries is not recommended for this set because their  
voltage and life is lower than standard batteries.  
16. Installation of batteries should be done by an adult only.  
SAVE THESE INSTRUCTIONS  
3
IB-CD163(TA)-FRED’S-E-042602  
CHOOSING THE POWER SOURCES  
You can use AC power or batteries as a power source.  
To a wall outlet  
NOTE: One blade of plug  
and outlet is wider.  
AC SOCKET  
1. Connecting the AC power  
cord  
Insert one end of the supplied AC power cord (located  
in the battery compartment) into the socket located  
at the back of the set, and the other end to the wall  
outlet.  
TIP  
If the plug of the AC power  
cord does not match your  
outlet, do not force it.  
Reverse it and try again.  
The plugs are polarized  
and only fit one way into the  
wall outlet and back of the  
set.  
2. Using battery power  
Insert 8 size “D” batteries (not supplied) into the  
battery compartment.  
To use the player on batteries, disconnect the AC  
power cord from the player.  
TIP  
Replace the batteries  
when the set stops  
operating. Replace all the  
batteries with new ones.  
Before you replace the  
batteries, be sure to take  
out the CD from the player  
and remember to check the  
Battery Safety Instructions  
on Page 3.  
UPPER  
LOW ER  
VFD DISPLAY  
The VFD display only lights up when using AC  
power.  
4
IB-CD163(TA)-FRED’S-E-042602  
ATTACHING THE SPEAKERS  
1.Bring one of the speakers to the right side  
of the set.  
2.Align the rails of the speaker box with the  
main set as shown in FIG.1.  
FIG.1  
3.When speaker align with the rails, push the  
speaker into the rails as shown in FIG. 2.  
4.Repeat above steps 1 to 3 for the left  
side.  
FIG.2  
5.Carefully unwind the speaker wire from behind each speaker box and plug the  
right plug into Speaker Jack R, also plug the left plug into Speaker Jack L (as  
shown in FIG. 3). Wrap the remaining wire behind each speaker box.  
LOCK TAB  
FIG.3  
NOTE: This set can be used with speaker boxes attached to the cabinet or  
separated, just make sure both speaker plugs are plugged into the jacks.  
To remove the speakers, press the lock tab and push the speakers out  
of the rails.  
5
IB-CD163(TA)-FRED’S-E-042602  
REMOTE CONTROL  
You can control the CD PLAYER with the provided REMOTE CONTROL (including the  
functions of POWER ON/OFF, MUTE, VOLUME control, CD REPEAT and PLAY features).  
NOTE: When you use the REMOTE CONTROL to operate the CD PLAYER,  
make sure the POWER switch on the main set is turned on, otherwise,  
the REMOTE CONTROL will have no functions to the set.  
1. POWER ON/OFF  
2. MUTE  
9
1
3. REPEAT - ONE & ALL SONGS  
4. PROGRAM  
5. VOLUME UP/DOWN  
6. SKIP/SEARCH BACKWARD  
7. SKIP/SEARCH FORWARD  
8. STOP  
8
2
3
7
9. PLAY/PAUSE  
4
6
NOTE: When you press the POWER  
ON/OFF switch to shut the set  
off, the STANDBY indicator on  
the main set will turn on.  
5
Slide the battery cover to remove. Insert two size “AAA” batteries correctly so that the +  
and - polarities match the polarity diagrams inside the battery compartment.  
NOTE:  
About half a year of normal operation can be expected when using the  
alkaline batteries.  
when the batteries are exhausted, the remote control will no longer  
operate the system. Replace both batteries with new ones.  
When the remote control is not to be used for a long time (2 months or  
more), remove the batteries to avoid possible damage that may be caused  
by battery leakage.  
Avoid keeping the remote control in extremely hot or humid locations.  
The remote control’s operating distance is about 0.2m (8 inches) to 6m  
(20 feet) away from the remote sensor.  
6
IB-CD163(TA)-FRED’S-E-042602  
PLAYING A CD  
3
1
2
5
6
Connect the supplied AC power cord or batteries (see page 4).  
POW ER  
Press the POWER switch, the VFD  
display will turn on and the  
STANDBY lamp will go off.  
1
2
STANDBY  
Set the FUNCTION switch to CD  
position, two dashes “--” will show  
on the VFD display.  
Open the CD DOOR by pressing the  
right corner marked OPEN/CLOSE  
and place the CD in the CD  
compartment.  
The label side of the CD should face  
upward.  
3
4
Close the CD DOOR by pushing it  
down. The display will show the total  
number of tracks (songs) on that  
CD.  
Press the CD PLAY button. The  
player will play all the songs (tracks)  
once in order.  
5
6
To change the sound effect, adjust  
the BASS and TREBLE knobs to  
your taste.  
TIP: “  
” WILL SHOW IN THE DISPLAY IF THERE IS NO DISC IN THE CD  
COMPARTMENT OR IF THE DISC IS UPSIDE DOWN.  
7
IB-CD163(TA)-FRED’S-E-042602  
USE THESE BUTTONS FOR  
ADDITIONAL OPERATIONS  
VOLUME CONTROL  
TIP  
When CD play is  
paused,  
will  
flash and no music  
will play.  
FUNCTION SWITCH  
To  
Press or Adjust  
Adjust the volume  
Stop playback  
VOLUME control  
To resume play,  
press the PAUSE  
STOP  
button again, “  
PLAY/PAUSE  
will stop flashing  
and music will play.  
” will flash during pause.  
Press again to resume play  
after pause.  
Pause playback  
TIP  
If you bump the set  
or the table it is  
sitting on, during  
CD play, the music  
will stop or skip for  
Go to the next track  
FORWARDS  
BACKWARDS  
Go back to the previous  
track  
a
few seconds.  
This is normal for  
this type of player.  
or  
Press and hold down while  
playing until you find the  
point.  
Locate a point in a song  
TIP  
This set has an  
electronic volume  
control, you may  
raise or lower the  
volume by pressing  
the  
control (“  
” ).  
Press the right corner of the  
CD DOOR marked OPEN/  
CLOSE (press STOP first).  
Remove the CD  
Turn off the power  
VOLUME  
“ or “  
Press the POWER switch, the  
display will go off and the  
STANDBY lamp will turn on.  
8
IB-CD163(TA)-FRED’S-E-042602  
REPEAT PLAY  
PLAYING CD SONGS (TRACKS) OVER AND OVER  
You can play CD tracks over and over in normal or programmed play modes (see  
page 10). (NOTE: To use this feature, you need to operate the set with the  
REMOTE CONTROL, because there is no REPEAT button on the main set.)  
POWER SWITCH  
REPEAT  
FUNCTION SWITCH  
1. Press the POWER switch, the STANDBY lamp will turn off and the display will  
light up.  
2. Set the FUNCTION switch to CD position.  
3. Select the track by pressing  
or  
, and then press  
.
4. Press the CD REPEAT button on the REMOTE CONTROL.  
To repeat  
Display shows  
Press  
a single track (song)  
Press the REPEAT  
button once  
“REP” will flash.  
REP  
Press the REPEAT  
button twice  
“REP” will be  
steady on  
all the tracks (all songs)  
programmed tracks  
During programmed play,  
“REP” is steady  
on  
press  
the  
REPEAT  
button twice  
To cancel Repeat Play  
Press the REPEAT button until the “REP” goes off.  
9
IB-CD163(TA)-FRED’S-E-042602  
PROGRAMMED CD PLAY  
SELECTING YOUR OWN MUSIC PLAYING ORDER  
You can make a program of up to 19 tracks to  
play in the order you want them to be played.  
NOTE: Programming is only done during  
stop mode and with REMOTE  
CONTROL.  
PROGRAM  
During STOP mode, press the  
PROGRAM button on the  
1
REMOTE CONTROL.  
” and  
“PRG.” will flash in the display.  
Press the SKIP/SEARCH buttons  
either or until the  
desired track shows in the  
display.  
2
3
Press the PROGRAM button. “  
and “PRG.” will flash in the  
display.  
Repeat steps 2&3 until all the  
desired tracks are programmed.  
4
5
Press the PLAY button to start  
programmed play. “  
” and the  
track number being played will  
show in the display, and “PRG.”  
will flash in the display.  
To change the current program  
Just create a new program following the programming procedure.  
To cancel Programmed Play  
Press the STOP button once, “PRG.” will disappear from the display.  
10  
IB-CD163(TA)-FRED’S-E-042602  
LISTENING TO THE RADIO  
3
4
1
2
6
Connect the supplied AC power cord or batteries (see page 4).  
POWER  
Press the POWER switch, the  
STANDBY lamp will go off and the  
VFD display will turn on.  
1
STANDBY  
Set the FUNCTION switch to  
RADIO position.  
2
3
Set the BAND switch to the proper  
band position (AM or FM), and set  
the FM MODE switch to STEREO  
or MONO.  
Tune into the station you prefer  
using the TUNING control. Adjust  
for the clearest sound.  
4
This indicator will light up when  
receiving FM Stereo broadcasts.  
5
6
TREBLE  
BASS  
You may adjust the BASS and  
TREBLE controls to change the tone  
of the set to your taste.  
11  
IB-CD163(TA)-FRED’S-E-042602  
USE THESE BUTTONS FOR  
ADDITIONAL OPERATIONS  
FM MODE  
FUNCTION  
VOLUME  
TIP  
To  
Press or Set  
If the FM broadcast is  
noisy, set the FM MODE  
switch from STEREO  
to MONO.  
Adjust the volume  
VOLUME control (“  
or “  
” ).  
Set the FUNCTION switch  
to TAPE position or press  
the POWER switch.  
Turn off the Radio  
This set has an  
electronic  
volume  
control, you may raise  
or lower the volume by  
pressing the VOLUME  
To improve broadcast reception  
Change position of the antenna for FM or FM Stereo.  
Move the set itself for AM.  
control (“  
” or “  
” ).  
12  
IB-CD163(TA)-FRED’S-E-042602  
PLAYING A TAPE  
2
1
3
4
Connect the supplied AC power cord or batteries (see page 4).  
POWER  
Press the POWER switch, the  
STANDBY lamp will go off and  
the VFD display will turn on.  
1
2
3
STANDBY  
FU LL  
REEL  
EM PTY  
REEL  
Set the FUNCTION  
switch to TAPE position.  
A
Press the STOP/EJECT  
INSERT THIS WAY  
button (DECK  
A
or  
DECK B) to open the  
tape compartment and  
insert a recorded tape.  
Close the door.  
STOP/EJECT  
Press the PLAY button.  
The player turns on and  
starts playing.  
4
5
PLAY  
When the set finishes  
playing one side of the  
tape, the set will stop. To  
hear the other side of the  
tape, flip the tape over,  
then insert and press  
PLAY.  
AUTO STOP  
A
13  
IB-CD163(TA)-FRED’S-E-042602  
RELAY PLAY  
2
1
5
4
3
Connect the supplied AC power cord or batteries (see page 4).  
To play tapes in DECK A and then DECK B, follow the steps below:  
POWER  
Press the POWER switch, the STANDBY lamp  
will go off and the VFD display will turn on.  
1
STANDBY  
Set the FUNCTION switch to TAPE  
position.  
2
Press the cassette PLAY button on  
DECK A, DECK A will play.  
3
PLAY  
Press the cassette PAUSE button on  
DECK B.  
4
PAUSE  
Press the cassette PLAY button on  
DECK B. When DECK A finishes playing,  
DECK B will start playing automatically.  
5
PLAY  
When the tape finishes playing on DECK  
B, the set will stop.  
6
14  
IB-CD163(TA)-FRED’S-E-042602  
USE THESE BUTTONS FOR ADDITIONAL  
CASSETTE TAPE OPERATIONS  
VOLUME  
CONTROL  
PAUSE  
PAUSE  
PLAY  
PLAY  
STOP/EJECT  
STOP/EJECT  
RECORD  
REWIND & FAST F.  
REWIND & FAST F.  
To  
Press or Adjust  
Press the VOLUME control (“  
Adjust the volume  
or “  
” ).  
STOP/EJECT button  
Stop playback  
Fast forward or rewind  
the tape  
FAST FORWARD button or  
REWIND button  
Pause playback  
PAUSE button  
Press again to resume play after  
pause.  
Eject the cassette  
STOP/EJECT button  
Insert your headphone plug into  
the PHONES jack (at the front of  
the set).  
To enjoy the music  
without disturbing others  
(headphones are not  
included)  
To shut power off  
Make sure cassette buttons are all  
up (stop) and STANDBY lamp is on.  
15  
IB-CD163(TA)-FRED’S-E-042602  
RECORDING ON A TAPE  
1
3
MICROPHONE JACKS  
4
2
Connect the supplied AC power cord or batteries (see page 4).  
POWER  
Press the POWER switch, the STANDBY  
1
2
lamp will go off and the VFD display will  
turn on.  
STANDBY  
OK  
NO  
Press the STOP/EJECT button (DECK  
B) to open the tape compartment and  
insert a blank tape. Select the program  
source (AM, FM, CD, or microphone)  
you want to record.  
A
STOP/EJECT  
To record from the CD player, set the FUNCTION switch to  
CD position, insert a CD and follow the steps to play a CD  
(see page 7).  
To record from a radio, set the FUNCTION switch to RADIO  
position, and tune into the station you want (see page 11).  
3
OR  
OR  
To record from the microphone, set the FUNCTION switch to  
the TAPE position, and plug the microphone(s) (not included)  
into either of the MIC JACKS. Speak into the microphone.  
To record from the DECK A, set the FUNCTION switch to the  
TAPE position, and follow the steps to play a TAPE (see  
page 13).  
THEN  
Press the RECORD button to start recording. (The PLAY  
button is depressed automatically.)  
4
RECORD  
To hear what you recorded, set the FUNCTION switch to  
TAPE position, then press REWIND and PLAY.  
5
REWIND PLAY  
16  
IB-CD163(TA)-FRED’S-E-042602  
USE THESE BUTTONS FOR  
ADDITIONAL OPERATIONS  
DUBBING SPEED  
SWITCH  
TIP  
STOP/EJECT  
PAUSE  
For best recording  
effect, use the AC  
power instead of  
batteries.  
Press or Set  
To  
To  
erase  
a
recording, just start  
a new recording,  
and the old one is  
a u t o m a t i c a l l y  
replaced.  
Stop recording  
STOP/EJECT button  
Pause recording  
PAUSE button  
Press the button again to  
resume recording.  
see page 21 for  
notes on cassettes.  
Adjust recording speed  
when copying tapes  
DUBBING SPEED switch  
from NORMAL to HIGH  
speed.  
Turn off the power  
Press the STOP/EJECT  
button and press the  
POWER switch, the VFD  
display will go off and the  
STANDBY lamp will turn  
on.  
17  
IB-CD163(TA)-FRED’S-E-042602  
SINGING ALONG WITH KARAOKE FUNCTION  
VOLUME  
2
MICROPHONE JACKS MIC VOLUME  
Connect the supplied AC power cord or batteries (see page 4).  
Set the KARAOKE switch (on the back of the set)  
to ON position.  
1
2
Insert microphone plugs into the microphone jacks.  
To avoid mic howling, lower the volume level setting  
first.  
NOTE: Microphones are not included, you may  
purchase microphones where you bought  
this set.  
To sing along with the CD player, set the FUNCTION  
switch to CD position, insert a KARAOKE CD disc  
and follow the steps to play a CD (see page 7).  
3
To sing along with the tape, set the FUNCTION  
switch to the TAPE position, insert a KARAOKE  
TAPE into deck A or B, and follow the steps to  
play a TAPE (see page 13).  
Press the CD PLAY/PAUSE button on the CD player  
or press the PLAY button on deck A or B.  
4
5
PLAY  
Adjust the volume controls (both the set’s VOLUME  
control and the MICROPHONE VOLUME control)  
to achieve the best effect.  
18  
IB-CD163(TA)-FRED’S-E-042602  
USE THESE BUTTONS FOR ADDITIONAL  
OPERATIONS  
VOLUME  
CONTROL  
MIC VOLUME TREBLE  
BALANCE  
BASS  
To  
Press or Adjust  
Adjust the MIC volume  
MIC VOLUME  
Adjust the CD or TAPE  
music volume  
VOLUME control  
BALANCE control  
Adjust the RIGHT & LEFT  
channel output.  
TREBLE  
BASS  
BASS or TREBLE  
controls.  
Adjust the sound effects  
for low and high tones.  
TIP: If there is squealing or howling (feedback) noise during KARAOKE  
use, move the microphone away from the speakers or turn down  
the volume. Set the KARAOKE switch to OFF position for better  
music play.  
19  
IB-CD163(TA)-FRED’S-E-042602  
PRECAUTIONS  
On Safety  
On Power Sources  
For battery operation, use 8 size “D”  
As the laser beam used in the CD  
batteries. We recommend alkaline  
batteries for longer life.  
player section may be harmful to the  
eyes, do not attempt to disassemble  
the cabinet.  
qualified personnel only.  
Refer servicing to  
If the batteries will not be used  
for a few weeks or more, remove them  
to avoid damage that can be caused  
by battery leakage.  
Should any solid object or liquid fall  
into the set, unplug the player, and  
have it checked by qualified personnel  
before operating it any further.  
On Operation  
On Placement  
If the set is brought directly from a  
Do not leave the set in a location  
cold to a warm location, or is placed  
in a very damp room, moisture may  
condense on the lens inside the CD  
player section. Should this occur, the  
set will not operate properly. In  
this case, remove the CD and wait  
about an hour for the moisture to  
evaporate. If the set has not been  
used for a long time, set it in the  
playback mode to warm it up for a few  
minutes before inserting a cassette.  
near a heat source, or in a place  
subject to direct sunlight, excessive  
dust or mechanical shock.  
Do not place the set on an inclined  
or unstable place.  
Do not place anything within 1 inch of  
the back of the cabinet. The  
ventilation holes must not be covered  
for the set to operate properly and  
prolong the life of its components.  
This set is designed to be played on  
If the set is left in a car parked in the  
a stable no vibration position. If you  
bump the set during CD play, the music  
will stop or skip for a few seconds.  
This is normal for this type of player.  
sun, be sure to choose a location in  
the car where the set will not be  
subjected to the direct rays of the  
sun.  
If you have any questions or problems  
Since a strong magnet is used for the  
concerning your player, please contact  
our customer service department at  
1-800-315-5885.  
(Monday - Thursday 09:00 AM - 05:00 PM,  
Friday 09:00 AM - 01:00 PM EST)  
speakers, keep personal credit cards  
using magnetic coding or springwound  
watches away from the speakers to  
prevent possible damage from the  
magnets.  
20  
IB-CD163(TA)-FRED’S-E-042602  
PRECAUTIONS (continued)  
Notes on CDs  
Notes on Cassettes  
Before playing, clean the CD with a  
Break off the cassette recording tabs  
cleaning cloth. Wipe the CD from the  
center out.  
from side A or B to prevent accidental  
recording.  
Side A  
Do not use solvents such as benzene,  
Tab for side A  
Tab for side B  
thinner, commercially available  
cleaners or anti-static spray intended  
for vinyl LPs.  
Do not expose the CD to direct  
sunlight or heat sources such as hot  
air ducts, nor leave it in a car parked  
in direct sunlight as there can be a  
considerable rise in temperature inside  
the car and result in a damaged CD.  
To record on a tape with its tab broken  
off, cover the respective tab hole for  
side A or B with adhesive tape.  
The use of a cassette with more than  
90 minutes of play time is not  
recommended except for long  
continuous recording or playback.  
Do not stick paper or stickers on the  
CD, nor scratch the CD.  
To reduce the chances of tape  
After playing, store the CD in its case.  
jamming or tangling, you should check  
that there are no loose layers of tape  
visible through the cassette center  
window. If any, tighten these loose  
layers of tape using a pencil before  
inserting the cassette into the set.  
If there is a scratch, dirt or fingerprints  
on the CD, it may cause a tracking  
error or skipping.  
21  
IB-CD163(TA)-FRED’S-E-042602  
MAINTENANCE  
Cleaning the Lens  
Notes for Storing  
Cassette Tapes  
If the lens becomes dirty, it may cause a  
skipping of sound during CD operation.  
Clean with a commercially available lens  
cleaner and blower.  
1. Do not put a tape near a magnetic  
field, such as a TV, or speaker.  
Magnetic fields may reduce the tape  
sensitivity or even erase the  
recording.  
2. Do not store tape for any length of  
time in a hot, moist or dusty place.  
Cleaning the Tape Heads  
Wipe the heads, the pinch roller and  
the capstan with a cleaning swab slightly  
moistened with cleaning fluid or alcohol  
after every 10 hours of operation for  
optimum playback and recording quality.  
After cleaning, insert a tape when the  
areas cleaned are completely dry.  
Cleaning the Cabinet  
Clean the cabinet, panel and controls  
with a soft cloth slightly moistened with  
water or a mild detergent solution. Do  
not use any type of abrasive pad,  
scouring powder, or solvent, such as  
alcohol or benzene.  
COTTON SWAB  
CAPSTAN  
PINCH ROLLER  
ERASE HEAD  
RECORD/PLAY BACK HEAD  
NOTE: In order to see and clean the  
head, you may have to press  
PLAY first.  
22  
IB-CD163(TA)-FRED’S-E-042602  
TROUBLE SHOOTING  
Problem  
Remedy  
Connect the AC power cord to a wall  
outlet securely.  
The power is not on.  
Make sure the batteries are inserted  
correctly and they are fresh.  
Make sure the FUNCTION switch is at the  
right position as you want.  
Adjust the volume.  
Unplug the headphones when listening  
through speakers.  
There is no sound.  
You may use battery power, the VFD  
display only light up when using AC power.  
VFD display does not light  
up.  
appears in the display  
Insert the CD with the label side up.  
even when a CD is in place.  
Make sure that the CD compartment is  
closed.  
Place the CD with the label side up.  
Clean the CD.  
Take out the CD and leave the CD DOOR  
open for about an hour to dry moisture  
condensation.  
CD does not play.  
Make sure the FUNCTION switch is at CD  
position.  
Clean the CD, or replace it if the CD is  
badly damaged.  
Place the player in a location free from  
vibration.  
The sound drops out.  
Check if your batteries are fresh.  
Replace all the batteries with new ones if  
they are weak, or bring the set near a  
window, or rotate the set.  
The sound is weak, or has  
poor quality.  
Make sure the safety tab on the cassette  
is in place (see page 21).  
Make sure the FUNCTION switch is at TAPE  
position.  
The RECORD button does  
not function/The tape does  
not play.  
Clean the erasing head (see page 22).  
Replace all the batteries with new ones if  
they are weak.  
The tape does not erase  
completely.  
Make sure the tape is inserted properly.  
Make sure the safety tab of the cassette  
is in place.  
The tape does not record.  
The sound is weak/The  
sound quality is poor.  
Clean the heads, pinch roller and capstan  
(see page 22).  
The tape has reached its end. Remove  
it, flip to the other side and re-insert.  
Cassette PLAY button pops  
up.  
23  
IB-CD163(TA)-FRED’S-E-042602  
SPECIFICATION  
General Description  
Power source:  
AC 120V, 60Hz 22Watts  
DC 8 size “D” batteries for set  
DC 2 size “AAA” batteries for Remote Control  
(Alkaline batteries are recommended)  
Speakers (2 ways):  
and  
2 - 54 ohm woofers  
2 - 34 ohm tweeters with crossover  
Output power:  
Dimensions:  
5.0W/channel  
1
Width: 24 / ”  
4
1
Depth: 8 / ”  
2
7
Height: 12 / ”  
8
Weight: 15.4LBs  
CD Section  
Any normal CD used in portable players  
760 - 800 NM  
Plays disc type:  
Laser wavelength:  
Tracking method:  
Frequency response:  
3 - spot error detection  
50Hz - 15kHz +1/-2 dB  
3.86 mm lens  
NOTE: This CD player will only play NORMAL music CDs (or CD-R CDs). This set  
will not play CDRW encoded discs.  
Tape Recorder Section  
Frequency response: Standard normal bias cassette tape,  
70Hz - 10kHz  
Radio Section  
Frequency range:  
FM: 88 - 108 MHz  
AM: 530 - 1700 kHz  
LENOXX reserves the right to make design and specification changes for product  
improvement.  
PROTECT YOUR FINE FURNITURE!  
WE RECOMMEND A CLOTH OR OTHER PROTECTIVE MATERIAL BE PLACED UNDER  
THE SET WHEN PLACING IT ON SURFACE WITH A NATURAL OR LACQUER FINISH.  
24  
IB-CD163(TA)-FRED’S-E-042602  
LIMITED WARRANTY  
We warrant this product to be free from defects in material and workmanship  
under normal use for a period of 90 days after purchase and we will repair it free of  
charge or replace it at no charge, should it become defective under this warranty,  
providing you submit proof of purchase (sales slip) with the set.  
During the initial 90 day period after original purchase, we will service or  
exchange, at no charge, the set that is returned to LENOXX ELECTRONICS  
CORP. After the initial 90 day period expires, and for a period of 12 months from  
original purchase, we will repair the unit covering any part(s) that need to be  
replaced at no charge, but will charge for the cost of labor, return postage paid by  
Lenoxx.  
This warranty does not apply to any products which have been subject to misuse,  
neglect or accident. This warranty does not cover broken cabinet. UNDER NO  
CIRCUMSTANCES WILL LENOXX ELECTRONICS CORP. BE LIABLE FOR ANY  
INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states do not allow the  
exclusion or limitation of incidental or consequential damages, so the above  
limitations or exclusions may not apply to you.  
This warranty gives you specific legal rights, and you may also have other rights  
which vary from state to state. The following charges apply to repairs beyond the  
warranty period: $45.00. Be sure to pack carefully and return postage paid insured  
together with your money order (personal checks will not be accepted) and sales  
receipt to :  
LENOXX ELECTRONICS CORP. 2 GERMAK DRIVE, CARTERET N.J. 07008  
For customer service  
Dial 1-800-315-5885  
(MONDAY - THURSDAY 9:00 AM - 5:00 PM, FRIDAY 9:00 AM - 1:00 PM EST)  
or Visit Our Website: http://www.lenoxx.com  
© 2002 LENOXX ELECTRONICS CORP.  
2 GERMAK DRIVE  
CARTERET, N.J. 07008  
MADE & PRINTED IN CHINA  
25  
IB-CD163(TA)-FRED’S-E-042602  

Motorola Personal Communicator V100 User Manual
LG Electronics CHOCOLATE MCDD0012301 User Manual
LaCie LaCinema Rugged HD User Manual
Krups Caff Duomo User Manual
Kenwood KDC C469FM User Manual
HTC MAGIC SAPP100 User Manual
Electrolux EBA 60002X User Manual
Curtis SCR4975 User Manual
Casio Cell Phone OMC811 User Manual
Black & Decker DCM675RF User Manual